Condition: ready for operation (used), functionality: fully functional, Year of construction: 2013, operating hours: 94,936 h, controller manufacturer: Siemens SINUMERIK 80 D, travel distance X-axis: 3,000 mm, travel distance Y-axis: 1,300 mm, travel distance Z-axis: 600 mm, feed rate X-axis: 100 m/min, TECHNICAL DETAILS Working Area X-axis: 3,000 mm Y-axis: 1,300 mm Z-axis: 600 mm B-axis: ±135° C-axis: n × 360° Speeds X / Y / Z axis: 100 m/min B / C axis: 540 °/s Acceleration Simultaneous: 17.3 m/s² X / Y / Z axis: 10 m/s² B / C axis: 200 | 100 rad/s² Maximum Positioning Accuracy Linear axes X / Y / Z: 0.03 mm Rotary axes B / C: 0.005° Maximum Positioning Deviation Linear axes X / Y / Z: 0.08 mm Rotary axes B / C: 0.015° MACHINE DETAILS Laser type: Solid-state laser TruDisk 3001 Laser output: 3,000 W Cutting gas: Nitrogen Control: Siemens SINUMERIK 80 D Operating Hours "Laser On" hours: 94,936 h Operating hours: 99,293 h EQUIPMENT Magnetic coupling Dynamic cutting optics with f = 150 mm FocusLine FastLine Cell ObserveLine Rotary changer D = 4,000 mm including safety backing Scrap conveyor 4× configurable control interface Valve terminal for 8 pneumatic clamps per side 2× load status indicator for rotary changer Extended compressed air supply on equipment panel including vacuum ejectors Cutting gas: compressed air Renishaw touch probe Measuring head (without probe) Measurement data processing 3× horizontal fixture interface Hsdpfxoxlctze Aacsfn Extraction ducting Protective enclosure for rotary changer including safety device, 1 window and column for control panel Status signal light (top & bottom) Video monitoring with camera Monitor mount Special installation Cooling unit KLH

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2008, laser power: 4,000 W, table length: 1,500 mm, table width: 3,000 mm, Equipment: cooling unit, No minimum price – guaranteed sale to the highest bidder! The machine was serviced in 2022 by an Amada specialist. The service protocol can be found attached to this listing! Hfodpfxoxgg Iro Aacon TECHNICAL DETAILS Laser power: 4 kW Table width: 3,000 mm Table length: 1,500 mm EQUIPMENT Ridel chiller Donaldson extraction unit 2 exchange tables

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2023, operating hours: 1,990 h, laser power: 12,000 W, sheet thickness steel (max.): 30 mm, travel distance X-axis: 3,100 mm, travel distance Y-axis: 1,580 mm, travel distance Z-axis: 100 mm, Bystronic ByStar Fiber 3015 Dynamic Edition F12000 from year of manufacture 2023 with only 1,990 cutting hours! Original machine price was approximately GBP 767,000! TECHNICAL DETAILS Travel X-axis travel: 3,100 mm Y-axis travel: 1,580 mm Z-axis travel: 100 mm Maximum Sheet Thickness (Cutting) Steel: 30 mm Stainless steel: 30 mm Aluminium: 30 mm Hsdpfx Aexlcz Eeacsfn Brass: 15 mm Copper: 12 mm Positioning Speed Maximum positioning speed (X/Y parallel): 120 m/min Maximum simultaneous positioning speed: 170 m/min Positioning Accuracy Bilateral axis repeatability (R): 0.025 mm Mean bilateral axis positioning deviation (M): 0.05 mm Edge detection accuracy: ±0.5 mm Workpiece Weight Maximum workpiece weight: 1,100 kg Maximum workpiece weight on both shuttle tables: 1,850 kg Table Change Time Shuttle table changeover time: 25 s MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 12,150 x 6,000 x 3,200 mm Machine weight: 11,000 kg Laser Source Laser source: Fiber 12000 Power: 12,000 W Adjustable range: 1,200–12,000 W Wavelength: Fiber Consumption Total power consumption (incl. exhaust, cooler): 27 kW Operating Hours Cutting hours: 1,990 h Power-on hours: 13,428 h EQUIPMENT Detection Eye BeamShaper NCT & KerfScan 2nd high-pressure cutting gas channel Prepared for N2 generator Internal dust extraction system Electrical cabinet position: top (mezzanine structure not included) Note: The machine has already been dismantled, is in storage, and is no longer connected to power.

Condition: ready for operation (used), functionality: fully functional, working width: 6,050 mm, bending angle (max.): 180 °, sheet thickness (max.): 1 mm, overall weight: 6,000 kg, opening width: 250 mm, TECHNICAL DETAILS Max. working width: 6,050 mm Max. sheet thickness: 1.5 mm Max. opening: 250 mm Max. angle: 180° Number of adjustable sequences: 8 MACHINE DETAILS Motor power: 4.5 kW Dimensions & Weight Dimensions: 7,300 mm x 1,800 mm x 1,550 mm Hjdpjxmgx Rjfx Aacofn Weight: 6,000 kg Control: Conventional EQUIPMENT Shear at rear side

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2004, machine/vehicle number: P-1843, actuation type: hydraulic, controller model: Siemens Sinamics G110, bending force (max.): 80 t, overall weight: 5,500 kg, TECHNICAL DETAILS Bending force: 80 t Lowering speed: 80 mm/s Safety distance: 1,500 mm MACHINE DETAILS Control: Siemens Sinamics G110 Dimensions & Weight Dimensions (L x W x H): 2,800 x 2,150 x 2,700 mm Hodpfjxlthcsx Aacofn Machine weight: 5,500 kg IP protection class: 54

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2019, operating hours: 13,265 h, sheet thickness steel (max.): 20 mm, sheet thickness stainless steel (max.): 15 mm, sheet thickness aluminum (max.): 15 mm, sheet thickness brass (max.): 6 mm, sheet thickness copper (max.): 6 mm, travel distance X-axis: 4,000 mm, travel distance Y-axis: 2,000 mm, TECHNICAL DETAILS X-axis: 4,000 mm Y-axis: 2,000 mm Maximum Speed: 140 m/min Control: SINUMERIK 840D SL Laser Excitation: Diode Module Chiller Unit: Air/Water LASER DATA - TRUDISK 3001 Laser Power: 3,000 W Sheet Thickness, Mild Steel: 20 mm Sheet Thickness, Stainless Steel: 15 mm Sheet Thickness, Aluminum: 15 mm Sheet Thickness, Copper: 6 mm Sheet Thickness, Brass: 6 mm MACHINE DETAILS Length: 11,150 mm Width: 6,650 mm Height: 2,200 mm Base Machine Weight: 12,000 kg Laser Beam On Time: 13,265 h (03.02.2023) Laser On Time: 3,172 h (03.02.2023) Hfjdpsxl T Rwjfx Aacon EQUIPMENT - Semi-automatic pallet changer - Laser beam guidance via fiber optic cable - Linear motor technology - Integrated control cabinets - Slag boxes - Laser diode positioning - TruDisk driven by machine - PierceLine - FocusLine - NitroLine - Transport and positioning device - Automatic nozzle cleaning - Universal laser cutting head - Protective window monitoring - ControlLine - Lens protective glass - Internet teleservice - Programmable gas pressure - FastLine - Multi-sheet processing - Condition monitor - Micro-welding - Central Link - CE certifications - Compact dust collector - Extraction unit - Automatic pallet changer (with light barriers)

Year of construction: 2014, condition: excellent (used), functionality: fully functional, Ermak Model EKM80/150MTB universal ironworking machine., Serial number 51273-B690FC. Year 2014. PUNCHING 80-Ton punching pressure Max diameter 40mm at 14mm thickness Max thickness 24mm at 24mm diameter. Throat depth 510mm Stroke length 70mm Cycles/min at 15mm stroke 35 pieces Table size 625 x 550mm Working height to die 1200mm FLAT SHEARING Flat Bar (Max. thickness) 300 x 20mm Flat Bar (Max width) 450 x 15mm Blade Length 475mm Angle Flange Trim 80mm Working Height 1020mm Hodpfxsvmzlco Aacefn ANGLE SHEARING At 90 Degree shearing 130 x 130 x 13mm At 45 Degree miter shearing 70 x 70 x 7mm Working height 1225mm BAR SHEARING Round Bar Shearing 45mm Square Bar Shearing 45mm Working height 1355mm NOTCHING Material thickness 12mm Rectangular notching width 52mm Rectangular notching depth 52mm V notcher ( side x side x T) 52 x 52 x 12 Working height 1015mm

Condition: as good as new (ex-display), functionality: fully functional, Year of construction: 2025, operating hours: 400 h, control type: CNC control, degree of automation: automatic, actuation type: electric, laser type: fiber laser, laser source manufacturer: max, laser hours: 250 h, laser power: 3,000 W, laser wavelength: 1,080 nm, sheet thickness (max.): 20 mm, sheet thickness steel (max.): 20 mm, sheet thickness stainless steel (max.): 10 mm, sheet thickness aluminum (max.): 8 mm, sheet thickness brass (max.): 6 mm, sheet thickness copper (max.): 6 mm, table length: 3,050 mm, working length: 1,520 mm, working width: 30 mm, working height: 100 mm, travel distance X-axis: 1,520 mm, travel distance Y-axis: 3,050 mm, travel distance Z-axis: 120 mm, feed rate X-axis: 80 m/min, feed rate Y-axis: 80 m/min, feed rate Z-axis: 18 m/min, cutting speed: 30 mm/min, positioning speed: 80 m/min, repeat accuracy: 0.05 mm, workpiece weight (max.): 1,500 kg, power: 12 kW (16.32 HP), input voltage: 400 V, input current: 30 A, input frequency: 50 Hz, type of input current: three-phase, type of cooling: water, compressed air connection: 7 bar, overall weight: 4,500 kg, total length: 5,500 mm, total width: 2,300 mm, total height: 2,490 mm, Equipment: CE marking, cooling unit, documentation/manual, dust extraction, emergency stop, fume extraction, Ex-demo machine, 3kw fiber laser, running great, we are just making room for new machines, comes with a 1-year warranty. Any questions or to arrange a viewing, please ask. Hodpfx Aaexghbtscsfn

Condition: excellent (used), Year of construction: 2015, Murata Muratec Wiedemann 'M2048TS' 200kN Punch Capacity Turret Sheet Metal Punch Press with Muratec CNC Control Hfsdpfoxnb Ivsx Aacon CNC Servo Motor Driven Ram; 1,250mm x 2,500mm Sheet Capacity (with no repositioning); Maximum Punch Thickness 6.35mm Mild Steel; Stroke Approx 160mm; 5.5kW Motor; 44 Number of Tool Stations x 4 Index; Steel Ball Table; Crash Sensor; Foot Switch Control; S/No. 14KX463570001. Modular Machine Guard Caging with Omron F3SJ Type Safety Light Curtain; Weight of Machine Approx 12,000 Kilos; Footprint Approx 3,800mm x 7,000mm; Plus Large Quantity of Tooling in (2) Steel Cabinets; Line Voltage 240V; Machine Voltage 415 Volt; Wiedemann Tooling.

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2010, shaft diameter: 100 mm, bending force (max.): 28 t, stroke length: 200 mm, Equipment: CE marking, documentation/manual, TECHNICAL DETAILS Capacity: 90 mm Shaft diameter: 100 mm Usable shaft length: 280 mm Roller speed: 4.6 rpm Bending force: 280 kN Stroke: 200 mm MACHINE DETAILS Hodpfxjxmgw Tj Aacofn Control: Conventional Motor power: 12.5 kW Dimensions (L x W x H): 1,600 mm x 1,600 mm x 1,800 mm Weight: 2,800 kg EQUIPMENT CE marking Documentation

Condition: excellent (used), functionality: fully functional, Year of construction: 2017, control type: CNC control, BYSTRONIC XACT SMART 225/4100 PRESSBRAKE CAPACITY 4100 MM X 225 TON YEAR 2017 TOOLING FULLY GUARDED Hfedpfxowxykas Aacon CNC CONTROL THIS MACHINE HAS JUST BEEN PURCHASED AND DUE WITH US IN THE NEXT WEEK . WE HAVE 2 MACHINES AVAILABLE IDENTICAL .

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2015, operating hours: 33,749 h, laser power: 4,000 W, sheet thickness steel (max.): 20 mm, sheet thickness stainless steel (max.): 15 mm, sheet thickness aluminum (max.): 10 mm, travel distance X-axis: 4,000 mm, travel distance Y-axis: 2,000 mm, travel distance Z-axis: 115 mm, workpiece weight (max.): 1,700 kg, TECHNICAL DETAILS X-axis: 4,000 mm Y-axis: 2,000 mm Z-axis: 115 mm Maximum workpiece weight: 1,700 kg Maximum speed: 140 m/min Controller: CNC Sinumerik 840D SL Positioning accuracy Positioning deviation Pa: 0.1 mm Average positioning accuracy Ps: 0.03 mm Laser data Maximum laser power: 4,000 W Wavelength: 10.6 µm Sheet thickness mild steel: 25 mm Sheet thickness stainless steel: 15 mm Hfodpfoxl T Rdox Aacsn Sheet thickness aluminium: 10 mm MACHINE DETAILS Length: 12,000 mm Width: 5,300 mm Height: 2,200 mm Weight: 14,000 kg Total system power consumption: 11–65 kW Beam-on time: 19,152 h (28.08.2025) Laser-on time: 33,749 h (28.08.2025) EQUIPMENT - Automatic longitudinal pallet changer - Longitudinal chip conveyor - Oil vaporizer unit - PierceLine - FocusLine - NitroLine - PlasmaLine - TruFlow 4000 CO2 laser with optimized standby mode - Maintenance-free radial turbine - High-frequency excitation - TASC laser control - Laser power control - Laser logbook - LensLine with status monitoring - Cutting head with 250 mm focal length - Quick-change cutting head unit (UTI) - ControlLine - Lens with RFID chip - ContourLine - Micro-welding - FastLine - AdjustLine - Internet remote services - FlyLine - Simple workshop programming

Year of construction: 1973, condition: like new (used), Used BRONX Heavy Duty Initial Pinch Pyramid bending rolls. Year of manufacture : 1973. MACHINE FORMERLY INSTALLED AT ROLLS ROYCE PLC IN DERBY UK. IMMEDIATELY FOR SALE AND NOW LOCATED IN BELGUIM WHERE IT CAN BE INSPECTED. SPECIFICATION CAPACITY Two sets of dimensions which are shown below as "Prebending & Rolling" and then "Rolling only". Material Mild Steel Mild Steel Tensile strength 28/32 tons/sq.in 28/32 tons/sq.in Maximum width 11’(3350mm) 11’(3350mm) Maximum thickness at this width 2” (50mm) 2½” (63.5mm) Minimum inside diameter of rolled cylinder at maximum capacity 30’ (762mm) 37 ½’ (953mm) Maximum thickness of plate when hot rolling (finished rolling temperature 850° C.) 4” (102mm) 5” (127mm) Minimum inside diameter of rolled cylinder at maximum capacity hot rolling 40” (1016mm) 50” (1270mm) MAIN PARTICULARS Diameter of all rolls - 27” (686mm) Body length of rolls - 11’2”(3403mm) Rolling speed - 12 f.p.m. (3600mm/min) Main drive motor - 150 H.P. Slip Ring Type Two bottom roll adjusting motors, each - 50 H.P. Slip Ring Type Combined operation of swing down bearing and top roll counterbalance - Hydraulically applied Hydraulic power pack motor - 10 H.P. Electrical equipment to be suitable for operation on a supply of - 400/440 volts, 3 phase, 50 cycles CONE ROLLING ATTACHMENT: To facilitate the rolling of taper or conical forms, a skid plate is fitted to the inside of the non-drive end housing. ELECTRICAL EQUIPMENT Motors: Main Drive - 150 H.P. half hour rated – slip ring screen protected – foot mounted type. Bottom Roll Adjustments - 50 H.P. half hour rated – slip ring screen protected – foot mounted type. Hydraulic Power Pack Motor - 10 H.P. continuously rated – Squirrel cage – screen protected – foot mounted type. Control Gear: Main Drive - Drum type reversing control gear with 5 minute rated wire wound resistances, designed to pass 100% full load on the first notch or operating position in each direction. The controller will be fitted with off position interlock and limit switch rings where necessary. Bottom Roll Adjustments - Drum type reversing control gear with 5 minute rated wire wound resistances designed to pass 100% full load on the first notch or operating position in each direction. The controllers will be fitted with off position interlock and limit switch rings where necessary. Hydraulic Power Pack - Direct-on-line contactor type starter, operated from a maintaining type push button station. Solenoid valves for operating cylinders are push button operated. Note: Hfedpfx Ash U Rzgjacon Full protection to be provided for all the above control gear by a circuit breaker, incorporating overload and no-volt protection. FEATURES AND EQUIPMENT Spare Roll included with the machine. LENGTH TBA MM WIDTH TBA MM HEIGHT TBA MM WEIGHT 95 tonnes NOTE: The information contained herein is provided in good faith, but however due to unforeseen errors or omissions cannot be binding as to accuracy.

Condition: excellent (used), functionality: fully functional, Year of construction: 2019, Faccin 3HEL - 3128 3 Roll Double Pinch powered Bending Rolls Hfsdpsw R T Tksfx Aacon Year: 2019 Model: 3HEL - 3128 Capacity: 3000mm x 15mm Top Roll Dia.: 285mm Side Roll Dia.: 265mm

Condition: used, Year of construction: 1988, Amada Promecam ITS 5020 CNC Pressbrake With Promecam CNC MB Control Maximum Tonnage 500 KN. Maximum Bending Length 2,000mm. Working Top Height 960mm. Intake 370mm. Maximum Stroke 105mm. Goose Neck 400mm. Sideplate Entry 1,690mm. Approx Speed 85mm/sec. S/No. ITS 050 20 107 (1988). Hjdpfoxnb Ehex Aacjfn With Assorted Tooling, Sick Safety Curtain & Foot Switches. Overall Dimensions W2,500 x D1,745 x H2,180mm. Weight 3,450kg.

Condition: used, Promecam CTH425 Powered Guillotine, Force 1300, Course 110, 2400mm Wide, Light Guards at Rear. S/No. 220. Country of Origin: France Pre-auction offers considered. Hfodpfx Aaoxnl Itscsn Please Note: These lots are located in Hertfordshire, UK. Unfortunately, there are no loading facilities on-site, dismantling and loading will be at the cost of the purchaser. All/Any tooling is being offered as specifically described.

Year of construction: 2018, condition: new, TECHNICAL CHARACTERISTICS • Punching capacity: 500KN / 50Tn • Punching: Ø31x12mm Hedpfodx Rd Uex Aacefn • Strokes per minute (15mm travel): 34 • Throat deep: 177mm • Stroke: 50mm • L angle at 90⁰: 80x80x8mm • Flat bars: 350x10mm • Round bars: Ø35mm • Square bars: 30mm • Triangular notching: 90x42x10mm • Bending station: 100x10mm • Motor: 3KW • Net weight: 950Kg

Condition: excellent (used), functionality: fully functional, Year of construction: 2021, control type: CNC control, degree of automation: semi-automatic, actuation type: hydraulic, controller manufacturer: Elgo, controller model: P40T, working width: 3,100 mm, cutting angle (min.): 0.5 °, cutting angle (max.): 3 °, stroke rate (min.): 8 1/min, stroke rate (max.): 20 1/min, sheet thickness (max.): 13 mm, sheet thickness steel (max.): 13 mm, sheet thickness stainless steel (max.): 8 mm, sheet thickness aluminum (max.): 10 mm, back gauge adjustment: CNC-controlled, back gauge: 1,000 mm, power: 22 kW (29.91 HP), input voltage: 400 V, input current: 45 A, input frequency: 50 Hz, type of input current: three-phase, overall weight: 12,000 kg, total length: 4,000 mm, total width: 2,200 mm, total height: 2,100 mm, number of support arms: 2, Equipment: CE marking, emergency stop, finger protection, foot remote control, safety light barrier, 2021 MVD B13-3100 Guillotine Shears with Elgo P40T Control – Very Good Condition For sale is a 2021 MVD B13-3100 Hydraulic Guillotine Shear, equipped with the advanced Elgo P40T CNC Control. This machine is in very good condition, having been installed in 2021. The MVD B-Series shears are built for precision, productivity, and reliability, offering powerful hydraulic cutting performance with CNC-controlled accuracy. Perfect for fabrication shops, subcontractors, and sheet metal production. Machine Make: MVD Machine Model: B13-3100 Machine Type: Hydraulic Guillotine Machine Capacity: 3m x 13mm Machine Year: 2021 ✅ Key Features 3100 mm cutting length – handles large sheet sizes with ease 13 mm sheet capacity (mild steel) – robust heavy-duty performance Elgo P40T CNC Control – programmable backgauge, stroke, and cutting settings Hydraulic swing beam design – consistent and accurate cutting results CNC backgauge system with motorised adjustment Rugged welded frame for stability and precision Front sheet supports and squaring arm for operator convenience Safety light guards for operator protection Very Good condition – 2021 model, very low hours 📐 Technical Specifications – MVD B13-3100 Guillotine Shears Cutting Length: 3100 mm Capacity (Mild Steel): 13 mm Hodpfx Aexddzqoacofn Capacity (Stainless Steel): ~8 mm Backgauge Travel: 1000 mm (CNC controlled) Control: Elgo P40T CNC touchscreen – programmable stroke, backgauge, cutting angle Stroke per Minute: 8–20 (adjustable) Cutting Angle: 0.5°–2.5° adjustable Throat Depth: ~100 mm Main Motor Power: 22 kW Hydraulic System: High-pressure precision hydraulics Dimensions (L×W×H): ~4000 × 2200 × 2100 mm Weight: ~12,000 kg 🌍 Condition Year of Manufacture: 2021 Control: Elgo P40T CNC Model: MVD B13-3100 Condition: Very Good – lightly used Ready for inspection and immediate delivery 🔑 Summary This 2021 MVD B13-3100 Hydraulic Guillotine Shear with Elgo P40T CNC Control offers 3100 mm cutting length, 13 mm capacity, and CNC accuracy. A modern, reliable, and powerful sheet metal cutting solution ideal for fabrication, subcontracting, and production facilities.

Condition: used, Year of construction: 2016, LVD Electra FL3015 3KW Fibre Laser Cutting Machine. S/No. 36445 (2016) Capacity 3000mm x 1500mm, Rofin FL030 Fibre Laser Source. S/No. 987 (2015) Thermotec Chiller Unit, Donaldson Torit DCE DFPro-4SPK, Extraction System, Infeed/Outfeed Shuttle Table, Light Guards. Country of Origin: Belgium Pre-auction offers considered. Hfedpfxoxnl Ele Aacsn Please Note: These lots are located in Hertfordshire, UK. Unfortunately, there are no loading facilities on-site, dismantling and loading will be at the cost of the purchaser. All/Any tooling is being offered as specifically described.

Year of construction: 2018, condition: new, TECHNICAL FEATURES • Punching capacity: 1100KN / 110Tn • Motor: 9KW • Throat depth: 510mm (SD version) • Punching capacity: Ø40x30mm or Ø34x34mm Hsdsdx Rdcjpfx Aacofn • Strokes per minute (20mm travel): 28 • Flats cutting station up to: 600x15mm or 400x20mm • Angle cutting at 90⁰: 152x152x13mm • Angle cutting at 45⁰: 70x70x7mm • Round & square bar cutting: Ø y ¨ 50mm • Notching station: 90x52mm (thickness13mm)

Year of construction: 2018, condition: new, TECHNICAL FEATURES • Punching capacity: 550KN // 55Tn Hedpfedx Rdiox Aacsfn • Motor: 5KW • Throat depth: “S” 250mm // “SD” 500mm • Punching capacity: Ø40x10mm o Ø20x20mm • Strokes per minute (20mm travel): 37 • Flats cutting up to: 300x15mm o 200x20mm • Angle cutting at 90⁰: 120x120x10mm • Angle cutting at 45⁰: 70x70x7mm • Round & square bar cutting: Ø y ÿ: 40mm • Notching station: 90x42mm (espesor 12mm)

Year of construction: 2018, condition: new, TECHNICAL CHARACTERISTICS • Punching capacity: 600KN / 60Tn • Punching: Ø40x11mm • Strokes per minute (15mm travel): 32 • Throat deep: 500mm • L angle at 90⁰: 120x120x10mm Hjdodx Rd Sepfx Aacofn • Flat bars: 350x15mm • Round bars: Ø45mm • Square bars: 40mm • Triangular notching: 100x42x10mm • Bending station: 150x10mm • Motor: 5.5KW • Net weight: 2012Kg

Condition: new, Year of construction: 2022, AVAILABLE FROM STOCK : Geka plasma cutting machine GCS P-4020 table size 4000 x 2000mm incl. plasma source Hypertherm 125A incl. PRONEST HYPETHERM NESTING SOFTWARE - GEKA CNC cutting table - Hypertherm Powermax 125A - cutting capacity: steel 25mm, stainless steel 20mm, aluminium 12mm - CNC control with GproCUT 2D CAD cutting software - Nesting included. - Country of manufacture Spain incl. CE conformity. - Heavy duty base for increased support and rigidity. - CNC Tex computer control with touch screen. - Linear guides on all axes for high repeatability. - Safety cutting head to prevent damage to the cutting head. - Rack and pinion gearbox with 70kg/cm servo motors. - Fully enclosed cable drag to protect cables from damage. - Movement speed 40 meters/min. - Resolution 0.01mm. - Optional automatic lubrication on all axes. - Optional, separate suction chambers in the machine bed. - Z-axis with integrated THC (Torch Height Control) to ensure automatic cutting distance between torch and material during the entire cutting process. - Torch anti-collision system (machine stops before any collision). - Laser pointer to check X and Y axes for zero reference. - The effective cutting area for P-4020 is 4000 x 2000mm. - Portal height Z = 100 mm. - Table with compartements for aspiration Hfedpfx Aaogypcljcjn

Condition: good (used), functionality: fully functional, Year of construction: 1991, sheet thickness steel (max.): 16 mm, cutting length (max.): 6,000 mm, HYDRAULIC SHEAR LVD MVSB 62/16 Serial number 18478 Yom 06/1991 TECHNICAL SPECIFICATIONS Max. sheet thickness St45 16 mm Cutting length 6200mm Distance between uprights 6400mm Gap 60mm Range back gauge 1000mm Min. cutting angle 0.5 ° Max. cutting angle 2.5° Min. number of strokes/min. 6 Max. number of strokes/min 25 Min. blade clearance 0.05 mm Max. blade clearance 1.6mm Motor power 30kW Approx weight 35000 Kg LxWxH 7100x2400x3000mm Hfedpfx Aajumhm Ajcen Accessories included; ELGO P85 “GO-TO” for back gauge Electrical adjustment of back gauge 1000mm 1 x Front support 2mtr, one with 90° square arm front support L2000mm Foot pedal Ball bearings on table Inclinable back gauge with manual hydraulic pump

Condition: reconditioned (used), functionality: fully functional, Year of construction: 1997, sheet thickness steel (max.): 16 mm, cutting length (max.): 4,000 mm, HYDRAULIC SHEAR LVD MVSB 40/16 Serial number 24159 Yom 1997 TECHNICAL SPECIFICATIONS Max. sheet thickness St45 16 mm Cutting length 4050 mm Distance between uprights 4250 mm Range back gauge 1000mm Min. cutting angle 0.5 ° Max. cutting angle 2.0 ° Min. number of strokes/min. 7 Hodpfsuipu Eox Aacofn Max. number of strokes/min 26 Min. blade clearance 0.5 mm Max. blade clearance 1.6 mm Motor power 22 kW Approx weight 20500 Kg LxWxH 4800x2170x2750mm Accessories included; Electrical adjustment of back gauge 1000mm with Go-to controller blade clearance and cutting angle adjustable. 1 x Front support 1500mm, one with 90° square arm front support 1 x Front support of 1500mm Foot pedal